What If? Garage
Designing1991 Toyota Camry LE

Electronics & wiring

AiM PDM32, Haltech Nexus R5, four CAN buses, custom BCM and HVAC boards

The full vehicle network is designed: power distribution, four CAN buses, and two custom control boards. The boards are drafts that haven't been reviewed or ordered yet.

Three looms, two batteries

The car is wired as three dedicated looms: engine, chassis, and infotainment and cameras. An AiM PDM32 power distribution module runs the chassis side, and the Nexus R5 powers the engine's own loads (fuel pump, cooling fans, starter trigger and A/C clutch).

A second, smaller electronics battery, charged through a DC-DC charger, runs the onboard computers so the voltage dip during cranking can never reboot them. The audio amplifiers stay on the main battery. Every ground meets at one star point, which the CAN buses need as a common reference.

Four CAN buses, one rule

The transmission controller has its own bus to the R5. The engine data bus carries the R5's stream to the PDM32. The body bus links the PDM32 with the custom boards and the steering column. AiM's own devices get a fourth. Tire pressure sensors get a separate run so their messages can't clash with the engine's.

The rule: the onboard computers only ever listen, never transmit. Their adapters are switched to listen-only before they open the bus. A crash on the computer side can never affect the engine or gearbox.

Body control module

A custom board drives the windows and locks: one STM32 microcontroller, eleven motor half-bridges with current sensing, and CAN with sleep and wake so the key fob works with the car off. It has its own fused feeds, so a blown motor fuse leaves the locks and CAN working.

Draft schematic and routed circuit board are done, along with a sealed clamshell case. A bench test rig is planned before it goes near the car.

HVAC controller

A second custom board moves the blend, mode and recirculation doors and talks over CAN. The PDM drives the blower, defroster and seat heaters. A few physical backup buttons work even if the touchscreen doesn't.

Clean shutdown

The car cuts power without asking Windows first, so the PDM32 runs a shutdown sequence: it presses each computer's power button, watches a signal that says the computer is still running, waits until it stops, then opens a relay to cut its power. A three-minute backstop covers a hung update.

BMW F10 steering column

The column, wheel buttons and paddles come from a BMW F10. A custom interface board reads the wheel's buttons over LIN and puts them on the body bus, where the infotainment uses them for media control.

Parts list

What it takes, and where each part stands. Prices are left off; part numbers aren't.

Power

  • Power distributionAiM PDM32Chosen
  • Electronics batterySmall battery charged by a DC-DC battery-to-battery chargerTo decide
  • I/O expansionAiM RIO02Chosen

Engine

  • ECUHaltech Nexus R5To confirm

Custom boards

  • Body control moduleSTM32G0B1, 11 × Infineon BTN9970LV, TI TCAN1043A-Q1, TE AMPSEALDraft design, not reviewed or orderedTo fabricate
  • HVAC controllerInfineon TLE94112EL, TI ISOUSB111, CANDraft design, not reviewed or orderedTo fabricate
  • Column interface boardBMW F10 wheel buttons (LIN) to the body busTo fabricate

Chassis

  • Steering columnBMW F10 column, wheel and paddlesChosen
  • Tire pressureAiM TPMS kit on its own CAN runChosen

Audio

  • DSP and ampsHelix V Eight DSP Ultimate, Helix M One XChosen

Photos

Circuit board being fitted by hand
Bench work on the electronics.

Progress

  1. Sealed cases for the custom boards

    Both custom boards get clamshell cases with the connectors held in a groove, a one-piece gasket, a breather vent, and a sealed connector for the window motor power.

  2. HVAC controller board designed

    A custom board moves the blend, mode and recirculation doors and talks to the rest of the car over CAN. The blower, defroster and seat heaters stay on the power distribution module. Draft schematic and circuit board layout done.

  3. A clean shutdown every time

    At key-off, the power module presses each onboard computer's power button, waits until it has shut down, then cuts its power. Windows never just loses power, even if a page has crashed.

  4. Body control module designed

    A custom module drives the windows and locks: one microcontroller, eleven motor drivers and CAN with sleep and wake, so the key fob works with the car off. Draft schematic and routed circuit board done, plus a plan for a bench test rig.

  5. Tire pressure monitoring

    Real per-wheel tire pressure sensors on their own CAN bus, so their messages can never clash with the engine's.

  6. Four CAN buses, one rule

    Separate buses for the transmission, engine data, the body and AiM devices. The onboard computers only ever listen, never transmit, so a crash on that side can never affect the engine or gearbox. A BMW F10 steering column joins the car with its own interface board.

  7. Wiring architecture, version one

    Three dedicated looms (engine, chassis, and infotainment/cameras) built around an AiM PDM32 and a Haltech Nexus R5, with a separate electronics battery so engine cranking can't reboot the computers.