Engine & fuel
2.3L EcoBoost, aftermarket forged internals, port-injected, built for 800 hp, tuned to 600 whp max
2.3L EcoBoost with aftermarket forged internals, on a Haltech Nexus R5, converted to port injection. The major parts are chosen; nothing has been bought yet.
Why the 2.3 EcoBoost
The first version of this idea, years before What If? Garage existed, was a Camry with a Supra drivetrain. The EcoBoost is what survived a real elimination process: the Ford 302 with GT40 heads, the Coyote 5.0, the Barra inline-six, BMW's B48 and N55, Honda's K-series, Toyota's 3S-GTE and the 1JZ-GTE were all evaluated and set aside.
It won on the things that matter for this car: it packages in a Camry engine bay, parts are easy to get in the US, the aftermarket is active, and it has real headroom.
The engine program
The long block gets pulled from a Mustang donor. Its factory internals don't stay, forged or not, so the trim doesn't matter. It's torn down, inspected and rebuilt to an 800 hp ceiling: a sleeved block and a full forged rotating assembly from the aftermarket, ideally Wiseco or Manley.
It is never tuned past 600 at the wheels (about 700 at the crank). An engine built to survive 800 and run at 600 is working inside its limits, and 600 whp in a roughly 3,100 lb rear-drive Camry is plenty. A Mountune dry sump handles oiling.
Three power modes
A knob on the console picks Normal (about 200 whp), Sport (about 400) or Track (about 600). The Nexus R5 doesn't swap whole tunes, so each mode is an axis on the tables that should change: boost target, target lambda, ignition, rev limit, throttle limit and traction control.
Track can't be selected by a bump: the knob has firm detents, and the ECU only accepts a mode change off the throttle.
Port injection and staged injectors
The factory engine is direct-injected, but Haltech doesn't run direct injection and the 600 whp map needs port injectors anyway. The direct injector ports get plugged and the high-pressure pump blocked off.
Eight flow-matched Bosch 980 cc injectors run in two stages, four primaries and four secondaries, on a fuel rail designed and machined in the shop. One big set of injectors would idle below the range where they meter accurately; staging keeps idle clean and still covers the top end. Base fuel pressure is 36 psi on a 1:1 regulator.
Fuel comes from a 15-gallon Aeromotive cell with an in-tank pump. Its pressure limit and the intercooler's 32 psi rating set the boost ceiling, not the turbo.
Turbo and intake
A BorgWarner EFR 8374 twin-scroll turbo on a custom twin-scroll manifold, since nothing suitable is sold. A Mishimoto air-to-air intercooler is rated well past what the engine will make.
Engine management
A Haltech Nexus R5 runs the engine on a fresh harness built around Haltech sensors wherever there's a choice: two MAP sensors, air and coolant temperature, oil and fuel pressure and temperature, a wideband, flex fuel, two knock sensors and a drive-by-wire pedal. Ford's crank and cam sensors, cam timing solenoids and coils stay.
Open question before buying the R5: confirming with Haltech that it can read the 2.3's crank and cam pattern with variable cam control.
Parts list
What it takes, and where each part stands. Prices are left off; part numbers aren't.
Long block
- EngineFord 2.3L EcoBoost long block from a Mustang donor, any trimBlock and head are kept; the factory internals are notChosen
- BlockSleeved, built to an 800 hp ceilingChosen
- Forged internalsFull aftermarket forged rotating assemblyIdeally Wiseco or ManleyTo decide
- Dry sumpMountune E063 dry sump kitChosen
Turbo and intake
- TurboBorgWarner EFR 8374, 0.92 A/R twin-scroll, internal wastegate (P/N 179357)Chosen
- Exhaust manifoldCustom twin-scroll T4Nothing suitable is soldTo fabricate
- IntercoolerMishimoto Universal R-Line MMINT-UR, air-to-air, 24 × 12 × 4 in coreChosen
Fuel
- InjectorsHaltech HT-080104: 8 × Bosch 0280158040, 980 cc/min, staged 4 + 4Chosen
- Fuel railStaged rail for primaries and secondariesDesigned and machined in the shopTo fabricate
- Regulator1:1 rising rate, 36 psi base pressureTo decide
- Fuel cell and pumpAeromotive 18660, 15 gal cell with in-tank A1000 pumpChosen
- Direct injectionFactory DI ports plugged, high-pressure pump blocked offTo fabricate
Management
- ECUHaltech Nexus R5Confirm 2.3 EcoBoost crank and cam support with Haltech firstTo confirm
- Sensors2 × 4-bar MAP, air temp, coolant temp, oil and fuel pressure/temp, wideband, flex fuel, 2 × knockChosen
- Throttle pedalBosch drive-by-wire pedalChosen
- Kept from FordCrank and cam sensors, cam timing solenoids, coilsChosen
- Power mode knob3-position detented rotary on a custom console panelTo fabricate
Photos
Photos go up here as the work happens.
Progress
Aftermarket forged internals, not factory
The plan used to be checking the donor's VIN and trim for the HPP version's forged internals. None of the factory internals stay, forged or not: the rebuild gets a full forged rotating assembly from the aftermarket, ideally Wiseco or Manley. That means any 2.3 Mustang works as a donor.
Staged injection on a shop-made fuel rail
Eight flow-matched Bosch injectors, four primaries and four secondaries, on a fuel rail designed and machined in house. One big set of injectors would idle below their accurate range; staging keeps idle smooth and still covers the top end.
A starting map, written ahead of time
A rough base map for the Nexus R5: enough to start, idle and warm up with every protection on and boost kept low. A professional tuner checks it before the engine ever runs. Still to confirm with Haltech: reading the 2.3's crank and cam pattern.
Turbo, intercooler and fuel cell chosen
A BorgWarner EFR 8374 twin-scroll turbo on a custom manifold (none is sold for this setup), a Mishimoto air-to-air intercooler, and a 15-gallon Aeromotive fuel cell with an in-tank pump. A fresh engine harness uses Haltech sensors wherever there's a choice.
Three power modes
About 200, 400 and 600 whp, picked with a knob. The engine is built to survive 800 hp but never tuned past 600 at the wheels.
Port injection over direct injection
Haltech doesn't run direct injection, and the 600 whp map needs port injectors anyway. The direct injector ports get plugged and the high-pressure pump blocked off.